Readers ask: How To Seal A Leaking Concrete Bird Bath?

How do I stop my concrete bird bath from leaking?

Temporary fix would be to put a few layers of cling film over the bowl part. This will hold the water for the birds for now. A longer term fix might be to use an epoxy filler in the crack but this woudl run to a few quid so a new bird bath would be the better option in the long term.

What can I use to seal a concrete bird bath?

Apply Sealant to Concrete Birdbaths



If water is seeping through the concrete, you may have to use sealant on the whole inner surface. If cracks are letting the water out, you can fill and seal them. Silicone caulk fills cracks permanently, and it comes in tubes that make application easy.

Should you seal a concrete bird bath?

Concrete is a porous material, and if water seeps into the pores and freezes, it expands, causing small cracks. You can take the following precautions to protect your concreate birdbath: Once a year, seal your bath with a non-toxic (water-based) concrete sealer. This will keep most water from seeping into the bath.

Is Flex Seal safe for bird baths?

Yes, Flex Seal liquid is safe to repair your bird bath with, once it’s been fully cured that is. Flex Seal will usually dry to the touch in about 3 to 4 hours and will be fully cured in 24 hours.

How do you seal concrete to hold water?

Apply a top coat of concrete sealer. Once the surface has been thoroughly cleaned, apply a concrete sealer. Thompson’s Concrete Care Sealer may be used on exterior concrete, brick, stucco and stone, and prevents water damage, resists chipping and cracking, and provides resistance to damage from freeze/thaw cycles.

How do you clean a cement birdbath?

Steps to Clean a Birdbath



Remove any large deposits of spilled seed, feces, debris or other contaminants. Use a solution of one part distilled white vinegar to nine parts water to scrub the birdbath thoroughly. Scrub the basin, lip, and any area of the birdbath where the birds can land, perch, drink or bathe.

What is the best product to seal concrete?

Epoxy concrete sealers are the most durable, making them good for sealing garage floors and high-traffic retail environments. Softer acrylic sealers, which require a sacrificial floor wax, are more affordable and popular for residential concrete floors, including basements.

Will Flex Seal hurt birds?

Is it Safe For Birds? In short, yes, Flex Seal is safe for use in your birdbath as long as it’s fully cured before you give birds access to it again. Flex Seal usually dries within three or four hours but isn’t fully cured for about 24.

How deep should the water be in a bird bath?

The water should be no deeper than 0.5 to 1 inch at the edges, sloping to a maximum of 2 inches deep in the middle of the bath. One of the best ways to make your birdbath even more attractive is to provide dripping water. Many birds find the sight and sound of moving water irresistible.

Can I put bleach in my bird bath?

The bleach should be well diluted, 200ml of bleach to 5 liters of water. It will need to be left for approximately 15 minutes, so cover the bird bath well. Tip the solution away, but be sure not to leave this water anywhere where it can be harmful to any birds or animals.

What is the best color to paint a bird bath?

Colors that bring birds to your backyard

• Blue – Bluebirds and jays.
• Earth tone shades – Skittish bird species.
• Gray, brown and green – Doves, quail, thrushes and other ground feeders.
• Orange – Orioles and hummingbirds.
• Red and pink – Hummingbirds.
• Yellow – Goldfinches, warblers, and hummingbirds.

Is Flex Seal permanent?

Q: How long will Flex Seal® last? A: Depending on the environment, coats added and maintenance, many people have found Flex Seal® will last for years without cracking, peeling or losing any of its strength or sealing properties.

Is Flex Seal safe for animals?

A: Yes, Flex Seal Liquid is safe around plants and animals (once fully cured).

How do you repair a cement birdbath?

That being said, cracks in your bird bath do not usually require time-consuming or expensive repairs.

1. Step 1 – Purchase Your Epoxy Filler.
2. Step 2 – Drain Bowl and Unplug Electrical Fixtures.
3. Step 3 – Clean the Bowl.
4. Step 4 – Mix the Epoxy.
5. Step 5 – Fill the Cracks.
6. Step 6 – Allow Your Bowl to Dry.
7. Step 7 – Refill the Bath.