Contents
- 1 How much does it cost to pour a 12×12 concrete slab?
- 2 Is it cheaper to pour your own concrete?
- 3 Can you pour concrete directly on dirt?
- 4 How much does it cost to pour a 20×20 concrete slab?
- 5 Is it cheaper to buy premixed concrete?
- 6 What is the difference between a concrete slab and a cement slab?
- 7 Do you need gravel under concrete?
- 8 What can I use instead of a concrete slab?
- 9 How much does an 80lb bag of concrete cover?
- 10 Should I put plastic under concrete?
- 11 Do you need rebar for 4 inch slab?
- 12 What is the best base for concrete slab?
- 13 How much would a 40×60 concrete slab cost?
- 14 How many bags of concrete do I need for a 10×20 slab?
- 15 How much does a 20×20 paver patio cost?
How much does it cost to pour a 12×12 concrete slab?
How much does a 12×12 concrete slab cost? The average cost to pour a 12×12 concrete slab that is 4” thick is between $888 and $1,584, with professional labor and materials included.
Is it cheaper to pour your own concrete?
One of the least expensive ways to get concrete is to mix your own. You can buy bags of the mix from a home improvement store. Typically, you only have to add water for it to be ready to pour. Otherwise, you risk getting a weaker concrete once it cures, which could lead to cracks or crumbles within a couple of years.
Can you pour concrete directly on dirt?
Long story short, yes you can pour concrete over dirt.
How much does it cost to pour a 20×20 concrete slab?
Concrete Slab Cost Calculator
Size (in feet) | Approximate Cost |
---|---|
12×20 | $1,440 |
20×20 | $2,400 |
24×24 | $3,460 |
20×30 | $3,600 |
Is it cheaper to buy premixed concrete?
It’s cheaper to do all the prep and buy the concrete premixed and delivered. For example, a 10×20′ slab of 4″ concrete would be a minimum of 2.5-3 yards. Here concrete is about $80/yard (closer to $70), or $240 for the concrete. That same slab would take 223 40-pound bags, or 112 80-pound bags.
What is the difference between a concrete slab and a cement slab?
What is the difference between cement and concrete? Although the terms cement and concrete often are used interchangeably, cement is actually an ingredient of concrete. Concrete is a mixture of aggregates and paste. The aggregates are sand and gravel or crushed stone; the paste is water and portland cement.
Do you need gravel under concrete?
Whether you pour concrete for a walkway or patio, a strong gravel base is required to prevent the concrete from cracking and shifting. Gravel is especially important in clay soil because it doesn’t drain well, which results in water pooling under the concrete slab and slowly eroding the soil as it finally drains.
What can I use instead of a concrete slab?
A. Concrete Alternatives Generally
- Greencrete.
- Mycelium.
- Ferrock and Ashcrete.
- Aircrete.
- Hempcrete.
How much does an 80lb bag of concrete cover?
bag provides 0.45 cubic feet of cured concrete. A 80 lb. bag provides 0.6 cubic feet of cured concrete. If you have concrete delivered it is sold by the yard (which is a cubic yard = 27 cubic feet).
Should I put plastic under concrete?
Recently, though, research has shown that the old traditional layer of 6-mil Visqueen (polyethylene plastic) under the slab is seldom effective for two main reasons: Although it may seem water-tight, this grade of material allows a lot of water vapor to pass through.
Do you need rebar for 4 inch slab?
No, you do not need rebar for a 4–inch slab of concrete on grade. A 4–inch-thick slab cast on the ground and in permanent contact with it will float and rebar is not required. Rebar is recommended on concrete measuring 5 – 6 inches thick.
What is the best base for concrete slab?
Most concrete contractors want a mix of coarse and fine aggregate to create a compactable base that is going to be safe for settlement and drainage. Crusher run (a mix of crushed stone and stone dust) is one of the best base materials for concrete flatwork.
How much would a 40×60 concrete slab cost?
How much does a 40×60 concrete slab cost? It would be about $8,500 to $12,000 for a 40×60 foot concrete slab, 6 inches thick. That’s based on national averages of around $5 per square foot for a fully engineered, finished concrete slab, including labor and materials.
How many bags of concrete do I need for a 10×20 slab?
A 60-pound bag yields. 017 cubic yards, and an 80-pound bag yields. 022 cubic yards. For a 10 x 10 slab, you would need 77 60-pound bags or 60 80-pound bags.
How much does a 20×20 paver patio cost?
A 20×20 brick paver patio costs $3,800 to $6,800. The average cost of pavers and base materials is $4 to $6 per square foot, while labor runs $6 to $11 per square foot. Get free estimates from masonry contractors near you or view our cost guide below.