Quick Answer: How To Move Shower Drain In Concrete Floor?

How do I move a shower drain to a concrete slab?

How to Move a Shower Drain in a Concrete Floor

  1. Step 1: Mark Cuts With Red Crayon.
  2. Step 2: Take Safety Precautions.
  3. Step 1: Cut With an Angle Grinder.
  4. Step 2: Break Concrete Into Smaller Pieces.
  5. Step 1: Dig Trench for New Pipe.
  6. Step 2: Purchase Correct Size Drain Line.
  7. Step 3: Cut Old Drain Line.
  8. Step 4: Reattach Old Drain Line Piece.

Can you move plumbing on a concrete slab?

Moving the Water Lines



The average cost for moving the plumbing in a 200 square foot kitchen with a slab floor is $2,000 to $7,000. And the cost for the pipes themselves ranges from $10 to $50 per linear foot. And this does not include any concrete work that it would take to get to the pipes.

How much does it cost to move a shower drain?

If you’re relocating the shower, expect to pay an extra $900 – $1,200 (same as the toilet). There are specific codes that plumbers must follow to make sure drains and vents are correctly angled and securely fitted.

You might be interested:  Question: Diy Concrete Pump?

Does the shower drain have to be centered?

The shower drain has to be at the lowest point of the shower floor, and so the floor has to slope down toward the drain from all directions. For showers that have a bench built in, placing the drain under the bench will keep it out of the way.

How do you install a floor drain in a concrete slab?

How to Install a Floor Drain in a Concrete Slab

  1. Prepare Your Space. While it’s easiest to install a floor drain prior to pouring your cement, you can do it after the floor has been set.
  2. Plan Drainage. New floors are easier to plan, as you can lay out the pipes in place and then install the floor over top.
  3. Dig Trenches.
  4. Pour New Concrete.
  5. Add a Drain Cover.

Can you run water pipes in a concrete floor?

During the initial building of a home that has a concrete slab foundation and basement level, any plumbing that runs under the home must be put in before the concrete is poured, since the plumbing runs in the dirt, not within the actual concrete.

Can you install a toilet on a concrete floor?

You can install a toilet on a concrete floor. It may seem intimidating, but installing a new toilet can be a DIY project that you can be proud of.

How is plumbing run on a slab?

There is no crawlspace or basement beneath, which means the plumbing is under the slab foundation. Concrete slab foundations that encase the home’s plumbing lines, also called under slab plumbing, could have pipes made of copper, cast iron, or galvanized steel and these materials are prone to decay over time.

You might be interested:  FAQ: Stained Concrete How To?

Is it easy to relocate a toilet?

Moving a toilet is not so much about moving the actual fixture—in fact, installing a toilet is a simple job that takes less than an hour—as it is about moving the drainage and the water supply plumbing to the new location. Once all of the plumbing is in place, installing the toilet is a relatively easy task.

Is it difficult to move plumbing?

Moving kitchen plumbing is very difficult if your house is on a slab foundation. Water pipes can often be rerouted through walls or ceilings, especially if you use flexible PEX pipe. However, because the drain needs to have pitch and be lower than the fixture, it requires cutting and jack hammering through the slab.

Can I move a sewer pipe?

If it’s a public sewer (serving more than one property) then you will need to gain permission from the water company to build over it, alter it or even touch it – if it’s a public sewer then the water authority own it.

Where should shower waste be positioned?

Low level (slim line) shower trays are often designed with the waste located in the innermost corner adjacent to the point where the two walls meet (there are exceptions to this) so for the sake of description we shall assume this to be the case.

Can a shower drain be connected to a toilet drain?

You cannot connect a shower to the toilet drain or what would be the waste arm. It needs to be piped within a properly vented branch, unless you revent the new shower line which I be leave you are under the IPC code would need to be wet vented.

You might be interested:  Quick Answer: How To Use Epoxy Paint On Concrete?

What is a flush floor shower?

This is what the installation of a flush shower tray looks like: Waste pipework is installed under the floor (to carry away the waste water from the shower to the soil pipe normally located on the outside of your house). The floor is replaced with a hole cut for the trap (which is attached to the pipe).

Leave a Reply

Your email address will not be published. Required fields are marked *