Quick Answer: How Many Bags Of Concrete Per Post Hole?

How many bags of concrete do I need for a post hole?

Mix two 50lb bags of concrete with water in a mixing tub or 5-gallon bucket. Add concrete into the hole and around the 4” x 4”. Depending on your climate, let concrete set up for 24 – 48 hours.

How much quikrete do I need for a post hole?

Remember, the depth of the post hole should be one-half of the above-ground post height. (Example: For a 6 feet above ground post, use a post with an overall height of 9 feet and place 3 feet in the ground). The calculator will indicate the number of 50 lb. bags of QUIKRETE® Fast-Setting Concrete you need.

How many bags of Postcrete do you need per post?

You’ll need to bury the posts at least 2ft In the ground. As for how many bags of postcrete you need per post, that’s purely dependant on how big you make the post holes. As a rule of thumb, when using standard post hole diggers, I average 1 bag per post. For larger holes I would allow 1.5 bags to 2 bags per hole.

You might be interested:  How To Color Existing Concrete?

How many bags of concrete do I need for a 6×6 post?

Buy a couple extra bags, if you don’t use them you can always return them. As I recall, a 60# bag of concrete is about. 5cf, so you’d need 3 bags per hole.

Is 2 feet deep enough for fence posts?

Project Instructions



The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet).

Can you put dry concrete in a post hole?

Fast-setting concrete is ideal for setting posts because there’s no mixing—you simply pour the dry concrete from the bag right into the hole, then add water.

Can I pour concrete in a hole full of water?

The water in the hole under the pipe can be sucked out with a wet-dry vacuum before and during the repair job.

Is quikrete as strong as regular concrete?

Quikrete fast setting concrete is just as strong as regular concrete. Concrete gets its strength from a chemical reaction that occurs over time during curing. After it’s had time to cure, which usually take 28 days to complete, Quikrete can reach strengths up to 5000 psi.

How do I keep my post level while concrete dries?

Fill the hole up to a depth of 8 inches from ground level with 1/2-inch drainage gravel. Use rough-cut gravel with sharp edges. It will hold the post better than smooth rock.

What is the difference between Postcrete and concrete?

Concrete takes several hours or a day or two to set. Postcrete sets in a few minutes, several tens of seconds, even, so you don’t have to support the post for nearly as long as you do with concrete.

You might be interested:  Question: How To Measure Cubic Yards Of Concrete?

What size hole does a bag of Postcrete fill?

Just over one bag per hole should be sufficient, blue circle postcrete suggest 1 bag will fill a 8 x 30 inch hole with a 4×4 post. You’re dimensions are slightly bigger than that so better to be safe than sorry and have a bit extra.

How big of a hole do I need for a 6×6 post?

A 6×6 post requires a 10″-diameter hole. Shovel a 6″ layer of gravel into the hole to provide drainage.

How many bags of concrete do I need for a 10×20 slab?

A 60-pound bag yields. 017 cubic yards, and an 80-pound bag yields. 022 cubic yards. For a 10 x 10 slab, you would need 77 60-pound bags or 60 80-pound bags.

Can pressure treated posts be set in concrete?

Simply setting the posts in concrete does create a condition that will accelerate rot in the bottom of the posts. With pressuretreated posts, the rot will be slow. Concrete should be poured around the post – no concrete under the post.

Leave a Reply

Your email address will not be published. Required fields are marked *