- 1 How many inches of gravel do you need for a concrete slab?
- 2 What size crushed stone for concrete slab?
- 3 What type of gravel is used for concrete?
- 4 How much gravel do you need under a garage slab?
- 5 Can you pour concrete directly on dirt?
- 6 Do you need rebar for 4 inch slab?
- 7 Do I need gravel under my concrete slab?
- 8 What is the best base for a concrete slab?
- 9 Can I use pea gravel under concrete?
- 10 What is #2 gravel?
- 11 How much crushed gravel do I need?
- 12 How much does a load of gravel cost?
- 13 How many inches of concrete do I need for a garage?
- 14 How do you prepare the ground for a concrete slab?
- 15 Is sand a good base for concrete?
How many inches of gravel do you need for a concrete slab?
A hand tamper is sufficient for packing gravel, but a plate compactor makes the job much easier, especially when preparing a large area such as a patio. Excavate the soil to a depth of 8 inches, allowing 4 inches for the gravel base and 4 inches for the concrete slab.
What size crushed stone for concrete slab?
Question: What size aggregate should be used to make the concrete for a 4 inch slab? Top Answer (37% of 40 votes): 3/4 inch crushed stone. Explanation: #57 rock (3/4) is best for strength.
What type of gravel is used for concrete?
Limestone: A sedimentary rock that is the most commonly used to make crushed stone in the United States. One of the most versatile rocks for construction, limestone is able to be crushed easily making it a primary rock used in ready mix concrete, road construction, and railroads.
How much gravel do you need under a garage slab?
If it holds its shape, it’s about right. The safest approach is to remove the topsoil and place a minimum 4-inch layer of compactible gravel or crushed stone as a base over the undisturbed subsoil.
Can you pour concrete directly on dirt?
Long story short, yes you can pour concrete over dirt.
Do you need rebar for 4 inch slab?
No, you do not need rebar for a 4–inch slab of concrete on grade. A 4–inch-thick slab cast on the ground and in permanent contact with it will float and rebar is not required. Rebar is recommended on concrete measuring 5 – 6 inches thick.
Do I need gravel under my concrete slab?
Because concrete is a very porous material, it will absorb any moisture that it contacts. This can cause pooling. Without crushed stone, pooling water will settle under it and erode your slab. Adding a layer of crushed stone will add proper drainage, as well as create a barrier between your slab and the ground.
What is the best base for a concrete slab?
Most concrete contractors want a mix of coarse and fine aggregate to create a compactable base that is going to be safe for settlement and drainage. Crusher run (a mix of crushed stone and stone dust) is one of the best base materials for concrete flatwork.
Can I use pea gravel under concrete?
If you use pea gravel beneath a patio, take a few simple steps to ensure the stability of the base before setting your surface stones, pavers or bricks. Click to see full answer. It should be ok to pour concrete over your gravel walk although you might want to give the concrete a little more depth along the sides.
What is #2 gravel?
This primarily 1″ crushed, washed gravel with a top size of 1-1/2″ is often used for drainage around perforated pipe, under concrete slabs, and as a coarse driveway topping for soft, very muddy driveways. Suitable as a coarse driveway topping.
How much crushed gravel do I need?
In the construction world, most materials are measured in cubic yards. Multiply the length (L), in feet, by the width (W), in feet, by the height (H), in feet, and divide by 27. This will tell you how many cubic yards of crushed stone you need. When using this equation, make sure all of your measurements are in feet.
How much does a load of gravel cost?
The cost of gravel ranges from $10 to $50 per ton, $15 to $75 per yard, $1 to $3 per square foot, or $1,350 per truck load depending on the rock type, volume, and travel distance.
How many inches of concrete do I need for a garage?
The concrete slab should be four-inches thick at least; it needs to be thicker if heavy equipment will rest on it. Building codes offer requirements for the concrete mix, which vary by region. The standards are expressed in terms of “compressive strength,” which boils down to the amount of water used in the mix.
How do you prepare the ground for a concrete slab?
Preparation is the most important aspect of pouring a concrete slab.
- Dig the ground down to the proper depth.
- Smooth out the ground with the flat side of a rake so that you have a level surface.
- Tamp the ground with a hand tamper or mechanical tamper.
- Pour 2 inches of small, rounded gravel for additional drainage needs.
Is sand a good base for concrete?
Pour concrete over a solid, well-drained base
of sand or gravel over clay and other poorly draining soils to provide even support.