- 1 Can you use Tapcons for ledger board?
- 2 How far apart should ledger bolts be?
- 3 How much weight can a ledger board hold?
- 4 Can you build a deck over concrete?
- 5 How do you attach 2×6 to concrete?
- 6 Should deck post be set in concrete?
- 7 How do you attach wood to concrete without drilling?
- 8 How do you attach wood to concrete?
- 9 What can I use to glue wood to concrete?
- 10 Can I attach a ledger board to wall studs?
- 11 Can you attach a ledger board to brick?
Can you use Tapcons for ledger board?
“Through bolts” are driven into brick or stone, then protrude through the ledger, where they are fastened with a nut. Lag bolts are driven through the ledger and the brick or siding and into the house’s frame. Tapcon style concrete screws can be used in place of through bolts in many cases.
How far apart should ledger bolts be?
Typically, you will need to install your bolts alternating high and low 2″ from the top and bottom of the ledger board. As a rule of thumb, bolts can be spaced 16″ on center for supporting joist span up to 12′ in length. Longer joists will require tighter bolting patterns.
How much weight can a ledger board hold?
The ledger is 10′ long so every foot of ledger must be designed to carry at least 200 lbs of load.
Can you build a deck over concrete?
Even if your patio is in terrible shape, you can deck over it. Cracks, craters and seasonal movement along cracks are no problem. (depending on the thickness of your decking and whether or not you put spacers under the sleepers). So any door thresholds adjoining the patio must be at least that far above the concrete.
How do you attach 2×6 to concrete?
Tapcon screws will be your easiest and cheapest means to mount a 2×6 to a concrete floor, by far. They will require a hammer drill to drill the holes in the concrete, but you can rent one from the store if you don’t have one. You could also use concrete expansion anchors too.
Should deck post be set in concrete?
There are several ways to set deck posts; we recommend attaching the posts to concrete footers above the ground. This helps to prevent wooden posts from rotting. Set footers a minimum of 6” below the frost line for your area to prevent movement during freezing temperatures.
How do you attach wood to concrete without drilling?
If you are willing to make holes in the concrete but do not want to buy the particular drill bit needed, then the simplest solution is to get nails for your project. Standard nails will not work on concrete, but some nails are made specifically for nailing wood to concrete. Cut nails will also work for this as well.
How do you attach wood to concrete?
The fastest and easiest way to attach most wood parts to concrete is to use a powder-actuated gun. To use it, load a special gun nail and a. 22 caliber gun shell into the barrel. Press the nose against the workpiece, pull the trigger and the shell will drive the fastener directly into the concrete.
What can I use to glue wood to concrete?
Quikrete 10 oz. Construction Adhesive is typically used for repairing broken concrete, bonding wall blocks to caps, and attaching wood to concrete and masonry surfaces. Quikrete 10 oz. Construction Adhesive is easy to use, needing only a caulk gun for application.
Can I attach a ledger board to wall studs?
MiTek’s WSWH Washer Head Structural Wood Screw can be used to attach a ledger to studs directly, through 1/2″ APA rated sheathing or through one or two layers of 5/8″ gypsum wallboard (drywall).
Can you attach a ledger board to brick?
You should never attach a deck to a brick wall. The brick veneer must have a minimum of a 1-inch air space between the brick and the framing, but it can be up to 4.5″. A lag screw or bolt extending to the front of the brick simply cannot support deck loads at that location.