Often asked: How To Apply Concrete Densifier?

What does a concrete Densifier do?

Densifiers are used on non-polished concrete mainly to reduce dusting and improve stain resistance. They contain an active substituent or carrying agent alkali or alkaline earth metal silicate, such as lithium, sodium, magnesium or potassium silicate, with lithium silicate being preferred.

How do you use concrete hardener?

Remove contaminants by washing the floor thoroughly and allow to dry completely. Apply two coats of Concrete Hardener at the rate of 1 litre per 4m2 per coat, allowing the first coat to dry for 4-6 hours before applying the second. Apply with a mop, hair broom or squeegee. Clean down equipment with water.

What is the best concrete Densifier?

When it comes to silicate sealers we feel the best densifier and hardeners are lithium based. Since lithium silicates will react with calcium hydroxide present in concrete to produce the same molecule that concrete naturally forms to hold itself together (C-S-H) we feel this is the strongest, most durable densifier.

Is concrete sealing necessary?

And concrete driveways should be sealed every four or five years to protect them from water penetration and to prolong their life. Many people believe that concrete driveways don’t need maintenance, so they may never apply a sealer. This is a good time of year for driveway work.

How do you burnish concrete?

1.1 Burnishing the concrete by steel trowelling shall be achieved by repeatedly working the surface of the concrete using either a hand trowel or mechanical trowelling machine until a lustre is produced on the surface of the concrete.

Does colored concrete fade?

Cement Colors Inc state that the color can’t fade, but the concrete can. Left unprotected or weakened by a poor mix design or finishing job, the surface of concrete “dusts” and erodes slowly until fine aggregate and sand particles are exposed. This same process occurs in colored concrete.

What causes dusty concrete?

Dusting is the white chalking and/or powdering of concrete at the surface. It is primarily caused by the slow disintegration of a weak top layer of concrete. This bleed water can carry finer particles and cement to the surface, forming a weak layer of concrete at the upper most top of the slab.

Why is floor hardener used?

Hardeners act as a strong adhesive for different floor coverings and surface treatments. Also, they prevent newly poured concrete from curling, a distortion of a slab into a curved shape by upward or downward bending of the edges. Hardeners are applied to new or existing slabs.

Can you spray on concrete sealer?

If you are applying a penetrating concrete sealer you can use either a garden variety pump-up sprayer such as the Echo 2 Gallon Sprayer found at homedepot.com retailing for $29.97 or a paint roller or even a paint brush.

How do you use lithi Tek 4500?

Pour the 1 gallon of Lithi–Tek 4500 into a 5 gallon bucket. Next add 2 gallons of water into the 5 gallon bucket. Mix the water and 4500 mixture well. You can then pour the mixture into a sprayer to spray apply, or you can dip a nap paint roller into the bucket and roll apply.

How do you apply sodium silicate to concrete?

The proper way to apply sodium silicate:

1. It should be applied in light, even coats; it should look saturated, but not oversaturated.
2. Don’t apply too many coats. After the first coat, it should be waited for 24 h to pass, and then apply another one.
3. Wait for the sealer to fully cure before applying paint.

How do you harden a concrete floor?

Tips on How to Speed Up Concrete Drying Time:

1. Use the correct amount of water in the mix. Too much water can increase the drying time.
2. Do not over-trowel or seal the surface.
3. Keep doors and windows closed, the HVAC running, and fans circulating the air.
4. You can also use dehumidifiers to remove moisture from the air.

How do you seal burnished concrete?

If a slab intended for a burnished finish has been trowelled impeccably the concrete polisher’s job is then only to thoroughly clean, lightly buff and then coat the floor with either an oil based or acrylic sealer.

Does polished concrete need to be sealed?

While small-scale pits or imperfections refract light, highly polished concrete reflects it. Ideally, polished concrete should be scratch-free and have a surface texture without abrasion points. Therefore, these properly polished floors would not rely upon a sealant to produce its gloss.