How To Run Pipe Under Concrete?

Can you run water pipes in a concrete floor?

During the initial building of a home that has a concrete slab foundation and basement level, any plumbing that runs under the home must be put in before the concrete is poured, since the plumbing runs in the dirt, not within the actual concrete.

How do you protect PVC pipe under concrete?

  1. Pour a 2-inch thick layer of gravel over the base of the trench.
  2. Mix enough concrete to fill the area you require using water and “hydraulic” cement powder; prepare the mix in a large, plastic container.
  3. Install a closet flange around the PVC pipe to add structure and to provide an anchor.

How do you dig a trench in concrete?

The following steps outline the most common method for cutting a trench in a concrete slab.



  1. Step 1: Determine Which Equipment is Best For Your Project.
  2. Step 2: Dust Management.
  3. Step 3: Prepare The Concrete Slab.
  4. Step 4: Create A Guide Cut.
  5. Step 5: Finish Your Cuts.
  6. Step 6: Remove Concrete From Trench.
You might be interested:  Question: How To Cut Expansion Joints In Concrete?

How deep do you bury drainage pipe?

I usually dig a trench about 12 to 14 inches deep for downspout drain lines. If the lot is fairly flat, the pipes will get deeper the farther they extend, as you should create 1/8 inch of fall for every foot the pipes run.

Can I bury PVC pipe in concrete?

2 Answers. PVC pipe embedded in concrete should be fine under most codes I’ve seen. You’d need to sleeve something like black, galvanized, or no-hub iron pipe, but PVC and ABS are impervious on any reasonable timeline (~hundreds of years.)

How long will copper pipe last in concrete?

This is because the copper pipes generally last 50 years or more. It is resistant to corrosion. It has anti-bacterial properties, and it is an economically and environmentally sound choice for potable water supply lines.

Is it OK to bury copper pipe in concrete?

Concrete in direct contact with copper would corrode it. 15mm copper pipes will need to move as they expand / contract with the heat produced. Think about using plastic push fit pipes instead Run them in a plastic waste pipe.

How do you connect PVC pipe to concrete pipe?

How to Fasten a PVC Pipe to a Concrete Pipe

  1. Make sure that the concrete pipe is the female end of the connection.
  2. Prepare the outside of the male end of the PVC pipe.
  3. Place concrete putty or sealant around the PVC pipe where it joins the concrete pipe.

Does concrete eat PVC?

A. According to Bernard Erlin, the principal chemicals in concrete that could conceivably attack plastics are calcium hydroxide, sodium hydroxide and potassium hydroxide. Erlin cites a table from Handbook of Chemistry and Physics stating that rigid PVC has excellent resistance to strong alkalies.

You might be interested:  Quick Answer: How To Install Glue Down Wood Flooring Over Concrete?

How deep can you bury PVC pipe?

At 18 inches, you can use THWN-2 conductors inside a continuous length of PVC conduit, which protects the wire all the way through the trench to the house. At 24 inches you can bury underground feeder cable, using PVC conduit to 18 inches below ground only where the wire comes up.

How do I build an underground dog fence under the driveway?

Here’s how:

  1. Use a chalk line to draw the new line you want to cut.
  2. Rent or buy a circular saw with a masonry blade.
  3. Cut the line.
  4. Lay in the underground dog fence wire.
  5. Use concrete caulk over it.
  6. Optional end protection – Protect the ends with waterproof splice kits and a small length of PVC pipe.

How much does it cost to bore under a driveway?

3.1 Construction Cost

Service/Product Price-Low Unit
Directional Boring – Rural $6.00 Foot
Directional Boring – Urban $8.00 Foot
Directional Boring – Rock $42.50 Foot
Conduit (2” HDPE) $0.75 Foot

Can I run Romex in garage?

Romex is a type of conductor that has non-metal sheathing. Under no circumstances should you leave it exposed. They should be run through studs, on top of joists or trusses, and secured every six feet or so as well as within 12 inches of any fixtures. This is according to most electrical standards.

Leave a Reply

Your email address will not be published. Required fields are marked *