Readers ask: How Much Concrete Do I Need For Fence Posts?

How many bags of cement do I need for a fence post?

Most fence post holes will need between 1 – 4 bags of concrete to securely hold the post in place. The best way to determine the size of the hole is: Diameter of the hole is 3 times the width of the fence post. Depth of the hole is one-third to half the above ground height of the fence post.

How much concrete do I need for a 4×4 fence post?

The general rule of thumb when setting a post is that the depth of the post’s hole needs to be 1/3 to 1/2 of the actual above-ground height of the post. So, six-foot-high fence posts ideally need to be buried three feet into the ground. The diameter of your post hole should be three times the diameter of your post.

You might be interested:  Readers ask: How To Cut Concrete Pavers With A Circular Saw?

How do you calculate concrete for fence posts?

Example Fence Post Concrete Calculation

  1. Calculate the post volume. Change post diameter to feet: 3.5” / 12 = 0.2917′ Find radius (½ of the diameter):
  2. Calculate the hole volume. Hole radius (3x post radius): 3 x 0.1458′ = 0.4374′
  3. Calculate concrete volume. Hole volume – post volume: 1.2026 – 0.1336 = 1.069 cubic ft.

How much sand and cement do I need for fence posts?

In terms of the ratio to use for a concreting fence posts, the best mix is a mix of 1:2:4 (1 cement, 2 sand, 4 aggregate). Concrete is always best mixed using a cement mixer to ensure it’s even, but if you only need to mix a little, hand mixing is ok (see mixing concrete project above for tips on how to do this).

Is 2 feet deep enough for fence posts?

Dig post hole so diameter of the hole is 3 times the width of the post (i.e., the hole for a 4” wood post should be about 12 inches wide). The depth of the hole should be 1/3-1/ 2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet ).

Should I use concrete for fence posts?

Concrete is the most secure material for setting fence posts, especially if you have sandy soil. Using premixed concrete rather than dry concrete will ensure ultimate security. While concrete is sturdy, it lacks the drainage of gravel and can trap moisture, ultimately leading to rot.

How long will a treated 4×4 post last in the ground?

The treated post that are rated for ground contact are guaranteed for 40 years.

You might be interested:  Quick Answer: How To Remove Concrete Patio Attached To House?

Can pressure treated posts be set in concrete?

Simply setting the posts in concrete does create a condition that will accelerate rot in the bottom of the posts. With pressure – treated posts, the rot will be slow. Concrete should be poured around the post – no concrete under the post.

How do you keep fence posts from rotting in concrete?

Consider Adding Posts to Concrete From here, you should fill the hole with about 6 inches of gravel. This will prevent rotting by ensuring that the post is kept dry when water makes its way into the soil. Place the post in the gravel, then fill with a batch of cement until it reaches the top of the hole.

Do you need gravel under concrete?

Whether you pour concrete for a walkway or patio, a strong gravel base is required to prevent the concrete from cracking and shifting. Gravel is especially important in clay soil because it doesn’t drain well, which results in water pooling under the concrete slab and slowly eroding the soil as it finally drains.

How do I keep my post level while concrete dries?

Fill the hole up to a depth of 8 inches from ground level with 1/2-inch drainage gravel. Use rough-cut gravel with sharp edges. It will hold the post better than smooth rock.

How many yards are in a 60 pound bag of concrete?

60 pound bag yields.017 cubic yards.

Can you put dry concrete in a post hole?

Fast-setting concrete is ideal for setting posts because there’s no mixing— you simply pour the dry concrete from the bag right into the hole, then add water. Under normal curing conditions, you can apply heavy weight to the post (a basketball backboard, for example) after just 4 hours.

You might be interested:  Quick Answer: Fiber Mesh Concrete?

How do I put a post in the ground without concrete?

Procedure:

  1. Find a concrete surface and lightly tamp your digging iron against it.
  2. Remove the turf and topsoil from the site of the post.
  3. Dig the hole putting the displaced earth onto the tarp.
  4. Pour 4 inches of gravel into the hole.
  5. Place the post in the hole.
  6. Add another 2 inches of gravel around the base of the post.

What’s the difference between Postcrete and concrete?

Concrete takes several hours or a day or two to set. Postcrete sets in a few minutes, several tens of seconds, even, so you don’t have to support the post for nearly as long as you do with concrete.

Leave a Reply

Your email address will not be published. Required fields are marked *