Quick Answer: How To Replace A Shower Drain In Concrete?

How do you install a Kerdi drain on a concrete floor?

Kerdi drain in concrete floor — a better way?

  1. Cut drain riser to correct length to position Kerdi drain just above the concrete floor.
  2. Cut 4″ ABS to the correct length to position the top of the coupler so that it will be touching the bottom of the Kerdi drain when installed.
  3. DRY FIT EVERYTHING!

Can I use concrete for shower floor?

Concrete is perfectly adequate, if not recommended, for use as the shower pan base for materials such as stone, tile or mosaic tile to be used as the finish surface (as long as there is a proper membrane between the concrete and any vulnerable surrounding material).

Do I need a shower pan liner on concrete floor?

JRC3 Member. It will need to be lined or it will wick into the slab and studding. The liner also makes the walls around the pan water-tight, that’s why the liner normally goes up at least 3″ above the pan behind the tile and backer material. Moisture gets behind the wall tile and is eventually caught by the liner.

You might be interested:  Often asked: How Many Yards Of Concrete In The Hoover Dam?

Can I pour concrete over PVC pipe?

you should never pour concrete on any pvc conduit or water pipes unless you wrap the pipes with a form wrap to allow expansion and contraction and any penetration thru the concrete or install a 4in or 6in sleeve under the slab to pass the pipes though.

How do I fill a hole in my concrete basement floor?

  1. Use a hammer and a cold chisel to level the bottom of the hole and undercut its sides slightly so the patch can’t pop loose.
  2. Brush on a concrete bonding liquid,
  3. Mix the concrete with water and scoop some into the hole.
  4. To burnish the surface very smooth, use a steel trowel (shown) on the final few passes.

How do you install a drain in a basement floor?

  1. Step 1 – Plan the Basement Floor Drain. First you need to plan the location of your basement floor drain.
  2. Step 2 – Find the Plumbing Pipes. Your basement should already have some plumbing pipes.
  3. Step 3 – Drill the Basement Floor Drain.
  4. Step 4 – Cut the Floor.
  5. Step 5 – Connect to the Sewer.
  6. Step 6 – Bury the Pipe.

How do you Slope a concrete floor drain?

You need 1/4 inch of slope for every linear feet of floor space. For example, a floor that extends 4 feet away from the drain should have 1 inch of overall slope. Mark this outer height mark along the wall with a pencil. Mix up some concrete mix in the mixer.

How do you install a floor drain in a garage?

Simply use a rake or shovel to place the soil back into the trench you dug. It may stand a little bit taller than the soil around it, but it will pack down with time. Once the trenches are covered, remove the covering over the drain hole in the garage. Install the drain cover, and your new drain is good to go.

You might be interested:  Quick Answer: How Many 80lb Bags Of Concrete In 1 Yard?

How do you dissolve hair in a shower drain?

Combining baking soda and vinegar is a natural way to dissolve hair clogs, without resorting to harsh chemicals. Pour a cup of baking soda down the clogged drain first, and then after a few minutes add a cup of vinegar.

How do you open a shower drain cover?

Hold the stopper body in place and unscrew the top knob (counterclockwise) with pliers and a rag or rubber grippy to prevent scratching. Unscrew the brass insert beneath with a flathead, then lift the stopper. From the open position, lift and look for a set screw. If no screw, simply turn counterclockwise to remove.

What is code for shower drain size?

A 2- inch pipe is the recommended size because showers have a low threshold for flooding, and a 2- inch pipe helps the water drain faster than does a 1 1/2- inch pipe. So, if you are converting from a tub and shower combination to a shower, you’ll likely have to change the drain pipe size.

Leave a Reply

Your email address will not be published. Required fields are marked *