Quick Answer: How To Lay Concrete Sidewalk?

How thick does a concrete sidewalk need to be?

Sidewalks should be at least 4″ (100mm) in thickness. Simple slabs for small foundations, bases, etc., normally 4″ to 6″ (100mm to150mm) thick, depending on the load they must bear. Slope the walk away from buildings to provide proper drainage.

Do you need gravel under concrete sidewalk?

Whether you pour concrete for a walkway or patio, a strong gravel base is required to prevent the concrete from cracking and shifting. Gravel is especially important in clay soil because it doesn’t drain well, which results in water pooling under the concrete slab and slowly eroding the soil as it finally drains.

Do you need wire mesh in concrete sidewalk?

It’s a heavy, heavy wire. But if you have reinforcing steel bars that go through it or the wire mesh, that makes it a lot stronger. Now in a sidewalk, typically they don’t put metal mesh in; they don’t put the mesh in there. But if it was like a driveway or a patio, they would.

You might be interested:  FAQ: How To Repair Concrete Driveway Holes?

Can you pour concrete directly on dirt?

Long story short, yes you can pour concrete over dirt.

What is the best concrete mix for sidewalk?

QUIKRETE® Concrete Mix is a good general-purpose mix for sidewalk and slab work. T-square, measuring tape, mason’s line, pickax, rake tample, hammer or half-hatchet, darby or bull float, hand float, finishing trowel, bricklayer’s trowel, edger.

Do you need rebar for 4 inch slab?

No, you do not need rebar for a 4 – inch slab of concrete on grade. A 4 – inch -thick slab cast on the ground and in permanent contact with it will float and rebar is not required. Rebar is recommended on concrete measuring 5 – 6 inches thick.

Do you need stone under concrete?

Because concrete is a very porous material, it will absorb any moisture that it contacts. This can cause pooling. Without crushed stone, pooling water will settle under it and erode your slab. Adding a layer of crushed stone will add proper drainage, as well as create a barrier between your slab and the ground.

What gravel do you put under concrete?

“Six inches of well-graded gravel or crushed stone material properly compacted will give good results,” said Mark Conrardy, a sales engineer manager for Wacker Corp., Menomonee Falls, Wis. When properly compacted, both native soils or imported granular materials can provide good support.

Can I use pea gravel under concrete?

If you use pea gravel beneath a patio, take a few simple steps to ensure the stability of the base before setting your surface stones, pavers or bricks. Click to see full answer. It should be ok to pour concrete over your gravel walk although you might want to give the concrete a little more depth along the sides.

You might be interested:  Quick Answer: How To Clean Concrete Driveways?

Is wire mesh better than rebar?

In summary, rebar vs wire mesh can have costly differences. Rebar remains stronger and ensures consistent contact in the soil where as wire mesh is unpredictable and often results in a week concrete foundation.

Can I use chicken wire to reinforce concrete?

Concrete reinforced with chicken wire or hardware cloth yields ferrocement, a versatile construction material. It can also be used to make the armature for a papier-mâché sculpture, when relatively high strength is needed.

Is it cheaper to pour concrete yourself?

One of the least expensive ways to get concrete is to mix your own. You can buy bags of the mix from a home improvement store. Typically, you only have to add water for it to be ready to pour. Otherwise, you risk getting a weaker concrete once it cures, which could lead to cracks or crumbles within a couple of years.

Should I put plastic under concrete?

Recently, though, research has shown that the old traditional layer of 6-mil Visqueen (polyethylene plastic ) under the slab is seldom effective for two main reasons: Although it may seem water-tight, this grade of material allows a lot of water vapor to pass through.

How do you prepare the ground before pouring concrete?

Preparation is the most important aspect of pouring a concrete slab.

  1. Dig the ground down to the proper depth.
  2. Smooth out the ground with the flat side of a rake so that you have a level surface.
  3. Tamp the ground with a hand tamper or mechanical tamper.
  4. Pour 2 inches of small, rounded gravel for additional drainage needs.

Leave a Reply

Your email address will not be published. Required fields are marked *