- 1 How do you repair concrete after removing tack strips?
- 2 How do you remove carpet from a concrete slab?
- 3 Do you remove tack strips when replacing carpet?
- 4 Can I remove carpet myself?
- 5 What is the easiest way to remove carpet?
- 6 Can I glue carpet tack strips to concrete?
- 7 What do you use to fill small holes in concrete floor?
- 8 What is best to patch concrete?
- 9 Will vinegar remove carpet glue?
- 10 How do you remove carpet glued to concrete?
- 11 Do I have to remove old carpet glue?
How do you repair concrete after removing tack strips?
- Wipe across the damaged concrete with a wire brush to remove cracked or chipped edges from the tack – strip nail holes.
- Sweep the area with a broom or small brush to remove any loosened concrete, dirt or other debris.
- Mix a quantity of epoxy concrete patch according to the manufacturer’s directions.
How do you remove carpet from a concrete slab?
- Cut the carpet into 3-foot-wide sections, using a utility knife.
- Pull back a corner of the carpet, using a pair of pliers.
- Remove the carpet padding by first removing the staples which hold it to the tack strips.
- Remove the glued perimeter of the padding by using a mechanical floor scraper.
Do you remove tack strips when replacing carpet?
Any rusted tack strips should be removed and the carpet guys or gals will put new ones in. You can leave the tack strips on your sub floor if you ‘re going to install new carpet. But, if you want to have new hardwood, laminate, or tile floors the tack strips need to be taken out.
Can I remove carpet myself?
If you find yourself pulling up one long piece, slice off sections as you go to make pulling easier. When you’ve torn off all the carpet and pad, pull out all the staples with pliers. You can pull staples with pliers, of course, but that can take hours.
What is the easiest way to remove carpet?
Pick a corner, grab the carpet with a pair of pliers, and pull. If the carpet comes up easily, grab it by your hand and continue pulling it up. If it doesn’t come up easily, use a utility knife to cut a 6-inch square in the corner. Remove the piece, then pull up the carpet by hand.
Can I glue carpet tack strips to concrete?
Place tack strip on floor and apply pressure along entire length to ensure strip is fully seated on the concrete or subfloor. Work quickly as open time of glue is 40 seconds • Hammer down nails, if present.
What do you use to fill small holes in concrete floor?
If you can ‘t find premixed concrete patch, you can make your own by mixing one part cement to 2.5 parts fine sand. To fill holes deeper then 1/4 inch, apply at least two layers of the cement patch. To make sure the patch sets properly, cover it with plastic sheeting for about five days.
What is best to patch concrete?
Vinyl Concrete Patcher is ideal for making smooth repairs to crack or chipped concrete floors, sidewalks or steps. It has strong adhesive properties allowing it to be applied down to a featheredge. Quikrete 10 lb. Vinyl Concrete Patcher is made of a special blend of vinyl resin, fine sand and Portland cement.
Will vinegar remove carpet glue?
To use white vinegar, mix one part white vinegar with one part hot water. Apply the white vinegar solution to the old carpet adhesive and let it sit for several minutes. The solution will soften the adhesive and start to dissolve it.
How do you remove carpet glued to concrete?
How To Remove Carpet Glue From Concrete Floor
- Step 1: Scrape the concrete glue. Scrape off as much of the concrete glue as possible.
- Step 2: Apply boiling water.
- Step 3: Scrub the loosened glue.
- Step 4: Apply glue remover.
- Step 5: Sand the floor.
- Step 6: Troubleshoot.
Do I have to remove old carpet glue?
Ripping up old carpeting is no small task, but removing the glue used to secure it to the subfloor is a major job all on its own. If you suspect the adhesive on your floor could contain asbestos, do not attempt to remove it yourself; contact an asbestos abatement professional.