- 1 Can you pour concrete directly on dirt?
- 2 Can I pour my own concrete slab?
- 3 How much does it cost to pour a 24×24 concrete slab?
- 4 What do you put under a concrete slab?
- 5 Do I need gravel under concrete?
- 6 Should I put plastic under concrete?
- 7 Is it cheaper to mix my own concrete?
- 8 Do you need rebar for 4 inch slab?
- 9 Can you pour a 2 inch concrete slab?
- 10 What is the difference between a concrete slab and a cement slab?
- 11 How much would a 4 inch slab of concrete cost?
- 12 How much does a 20×20 concrete patio cost?
- 13 What is the best base for a concrete slab?
- 14 How many inches of gravel do you need for a concrete slab?
- 15 Is quikrete as strong as regular concrete?
Can you pour concrete directly on dirt?
Long story short, yes you can pour concrete over dirt.
Can I pour my own concrete slab?
Used for walkways, patios, and floors, concrete slabs are inexpensive to install and durable enough to last for years. When you pour your own concrete slab, you’re giving yourself a design material that is adaptive to all of your needs.
How much does it cost to pour a 24×24 concrete slab?
To pour a typical 10×10 concrete slab will cost $670 to $930, a 12×12 slab for a patio will cost $796 to $1,476, a 20×24 driveway slab runs between $1,440 and $3,360, and a 24×24 slab for a garage will cost $3,058 to $5,944. Get free estimates from concrete companies near you.
What do you put under a concrete slab?
Because concrete is a very porous material, it will absorb any moisture that it contacts. This can cause pooling. Without crushed stone, pooling water will settle under it and erode your slab. Adding a layer of crushed stone will add proper drainage, as well as create a barrier between your slab and the ground.
Do I need gravel under concrete?
Whether you pour concrete for a walkway or patio, a strong gravel base is required to prevent the concrete from cracking and shifting. Gravel is especially important in clay soil because it doesn’t drain well, which results in water pooling under the concrete slab and slowly eroding the soil as it finally drains.
Should I put plastic under concrete?
Recently, though, research has shown that the old traditional layer of 6-mil Visqueen (polyethylene plastic ) under the slab is seldom effective for two main reasons: Although it may seem water-tight, this grade of material allows a lot of water vapor to pass through.
Is it cheaper to mix my own concrete?
One of the least expensive ways to get concrete is to mix your own. You can buy bags of the mix from a home improvement store. Typically, you only have to add water for it to be ready to pour. Otherwise, you risk getting a weaker concrete once it cures, which could lead to cracks or crumbles within a couple of years.
Do you need rebar for 4 inch slab?
No, you do not need rebar for a 4 – inch slab of concrete on grade. A 4 – inch -thick slab cast on the ground and in permanent contact with it will float and rebar is not required. Rebar is recommended on concrete measuring 5 – 6 inches thick.
Can you pour a 2 inch concrete slab?
If done properly, new concrete can often be poured right over an existing slab. For this to be feasible, the contractor needs to pour at least 2 inches thick, use smaller aggregate, and incorporate reinforcement such as welded wire mesh or fiber mixed into the concrete.
What is the difference between a concrete slab and a cement slab?
What is the difference between cement and concrete? Although the terms cement and concrete often are used interchangeably, cement is actually an ingredient of concrete. Concrete is a mixture of aggregates and paste. The aggregates are sand and gravel or crushed stone; the paste is water and portland cement.
How much would a 4 inch slab of concrete cost?
It costs about $6 per square foot to pour concrete, or between $4 and $8 per square foot. Concrete Work Cost by Thickness.
|Thickness||Typical Cost With Labor|
|4”||$5.35 per square foot|
|5”||$5.80 per square foot|
|6”||$6.20 per square foot|
|8”||$7 per square foot|
How much does a 20×20 concrete patio cost?
Cost to Install Concrete Patio by Size
|Size in Feet||Square Footage||Price Range|
|12×14||168||$1,400 – $4,000|
|15×15||225||$1,800 – $5,500|
|16×18||288||$2,300 – $7,200|
|20×20||400||$3,000 – $10,000|
What is the best base for a concrete slab?
Most concrete contractors want a mix of coarse and fine aggregate to create a compactable base that is going to be safe for settlement and drainage. Crusher run (a mix of crushed stone and stone dust) is one of the best base materials for concrete flatwork.
How many inches of gravel do you need for a concrete slab?
Excavate the slab area to a depth of about 7 inches, allowing 3 inches for a gravel base and 4 inches for concrete.
Is quikrete as strong as regular concrete?
Quikrete fast setting concrete is just as strong as regular concrete. Concrete gets its strength from a chemical reaction that occurs over time during curing. After it’s had time to cure, which usually take 28 days to complete, Quikrete can reach strengths up to 5000 psi.